Latest Cases
We Are Dedicated To Provide
Quality Service
Molding Complex Geometry in BMC: Flow and Thin Walls

Date | 2022-11-23 15:51:33

Two numbers decide whether a complex part can be molded in BMC at all: how far the compound has to travel before it reaches the last detail, and how thin the thinnest section is. Both are constraints on the process rather than on the material alone. A geometry that looks generous in a CAD model can be unreachable in a real tool if the flow front has to cross two ribs and a deep pocket before it gets there.

BMC flows as a paste with fibre in it, not as a low-viscosity liquid. That single difference explains most of the design rules that follow. The fibre resists being stretched around sharp corners, the filler loads the front so it moves as a mass rather than a stream, and air trapped ahead of the front has nowhere to go unless the tool provides somewhere.

How far the compound will travel

Flow distance is usually discussed as a ratio to wall thickness, and the ratio falls quickly as the wall thins. A part with a generous wall can be filled from a single central gate; the same footprint with a thin wall needs multiple gates, a warmer mold or a lower-viscosity grade, and sometimes all three. Increasing mold temperature helps the compound move, but the working window is bounded: run above the qualified range and the material cures before the cavity is full, or flashes where the tool cannot close.

Gate position is therefore a design decision rather than a toolmaking detail. It sets which details fill last, where the flow front meets itself, and which direction the fibre ends up pointing along the loaded section. Moving a gate on paper costs nothing; moving it after the tool is cut costs a weld and a re-qualification.

Weld lines, air traps and the defects they leave

Where two flow fronts meet, the fibre does not knit through the boundary the way it does in the bulk, and the result is a weld line with reduced strength and often a visible witness. Where the front closes around a feature, air is trapped unless a vent sits at that point. Both are predictable from the fill pattern, and both are cheaper to design out than to argue about after first-off.

DefectCauseDesign answer
Short shot at a far detailFlow distance exceeds what the wall and temperature allowAdd a gate or a runner, thicken the path, or reduce the distance
Weld line in a loaded areaTwo fronts meet; fibre does not cross the boundaryMove the gate so the meeting line falls in a low-stress region
Air trap / burnt spotFront closes around a feature with no ventVent at the last point to fill; avoid closed pockets
Fibre accumulation at a cornerSharp turn filters the fibre out of the flowGenerous radii on internal corners; avoid knife edges in the flow path
Deformation after demoldingUneven wall, uneven cooling, ejection too earlyBalance wall and cooling; eject at the qualified cure

Thin walls change the flame requirement too

Thin sections are not only a filling problem. A wall that is reduced to save space also has less material between the flame and whatever is behind it, and many flame ratings are thickness-dependent. This is the reason a thin-wall claim has to be read together with the thickness it was tested at: V-0 at 0.4 mm is a genuinely different statement from V-0 at 1.6 mm, and the first one is what allows a compact device to keep its rating while the wall gets thinner.

Thin walls also make the electrical margin less forgiving. Dielectric strength is quoted per unit thickness, but the actual breakdown of a part depends on the local wall, on voids and on the radius at an edge. A wall that is nominally correct but locally thinned by a flow mark has less margin than the drawing suggests, which is another reason to treat a cosmetic defect in a thin section as a functional one.

Frequently asked questions

Q1: Is there a minimum wall thickness for BMC?

There is no single figure, because the limit depends on flow distance, on the smallest feature that has to fill, and on the grade. What can be said is that the limit is set by the ratio of flow length to thickness rather than by thickness alone, so a thin wall in a small part is much easier than the same wall at the far end of a large one.

Q2: Can a weld line be eliminated completely?

In a part that fills from more than one front, no. It can be moved into a region where it does not carry load and where it does not show, and its appearance can be improved by keeping the mold hot and the fronts meeting at high pressure. What matters is that the location is chosen deliberately rather than discovered at first-off.

Q3: Does a thinner wall cure faster?

The thin section reaches temperature faster, but the cycle is set by the thickest section, not the thinnest. A part with one thick boss and a thin field will run at the cycle the boss needs, and the thin area will be over-cured as a result. Where a thick feature is unavoidable, it is often worth designing it as a separate insert rather than as part of the main wall.

For technical data sheets, grade recommendations, or a discussion about your specific geometry and flame requirement:

📧 wendy.qiu@smcbmc.com  📞 +86-13868305300