Latest Cases
We Are Dedicated To Provide
Quality Service
Molded-In Inserts in BMC Electrical Parts

Date | 2022-11-23 15:51:42

Molding a metal insert into a BMC part replaces an assembly step with a tooling risk. Done well, the insert is located to a tolerance the assembly could not achieve by hand, and the joint is as strong as the surrounding material. Done badly, the insert moves a fraction of a millimetre under pressure, the material around it cracks on cooling, and the failure appears at the customer rather than at the press.

The engineering question is not whether to mold the insert in place but how it will be held while the compound flows around it. That single decision drives the tool design, the cycle, the allowable wall around the insert and, in the end, whether the part can be made at a competitive rate.

Three ways to hold an insert, and what each costs

The simplest method is a pin or a spigot in the tool that the insert sits over. It locates accurately and costs almost nothing, but it leaves a hole in the part that has to be acceptable or plugged, and the pin itself becomes a wear item. A magnetic or vacuum seat holds the insert without a witness mark, which suits visible parts, but it depends on the insert material and adds a check to every cycle.

The third method is a machined seat with a shoulder, where the insert is pressed into a pocket and held by fit rather than by a fixture. It gives the best location and the cleanest surface, and it demands the tightest tolerances: both the insert and the pocket carry a tolerance, and the combination has to close before the compound arrives.

Where insert molding fails

The failures cluster around three mechanisms: movement under flow pressure, stress from differential expansion, and inadequate material around the insert. The table sets out how each one presents and what the design answer is.

FailureMechanismDesign answer
Insert pushed off positionFlow pressure acts on the insert before the material around it stiffensGate away from the insert; support on the downstream side as well as the seat
Crack around the insertMetal expands more than cured BMC; the material is in tension after coolingAdequate wall around the insert; avoid sharp corners at the seat
Insert pulls out under loadReliance on adhesion or friction aloneKnurl, groove or undercut the insert so the material keys into it mechanically
Flash collar at the insertAnnular clearance between insert and seat fills with compoundStep the seat so it bears at the cavity face; close the gap where it is visible
Insert thread filled with compoundCompound reaches the thread during fillingSeal the thread with a pin or a cap in the tool; specify a masking step

Design rules worth fixing early

The first rule is that an insert needs material all round it. A boss that is too thin around a metal core will crack at the corner during cooling, and the crack may not appear until the part has been in service for a while. Generous radii at the base of the boss, and a wall thickness that stays in proportion to the surrounding material, do more for insert integrity than any change of grade.

The second is that the insert should be keyed rather than glued. Knurling, a groove or a shoulder gives the cured material something to hold, so pull-out strength comes from geometry rather than from surface adhesion. The third is to keep critical dimensions away from the insert boundary: a length measured across the metal-to-compound transition combines two different thermal behaviours and will move more than the drawing implies.

Mold design and manufacture at Wenzhou Jintong follows Q/JTJ0003-2025, the company standard for thermosetting mold design and manufacture, which covers insert seats and their fit alongside the parting-line and venting requirements. Because the same standard governs the material and the compression molding process, an insert problem can be traced across tool, material and cycle instead of being argued between suppliers.

Frequently asked questions

Q1: Is insert molding cheaper than assembling afterwards?

Usually, at volume, and rarely at low volume. Molding the insert removes a handling and fastening step and gives better location, but it adds tooling complexity, a manual loading step in the cycle and a scrap risk if an insert is misplaced. The comparison has to be made on total cost at the expected quantity, including the cost of a rejected part that already contains a metal insert.

Q2: Can any metal be molded into a BMC part?

Most common insert materials are used, but the choice affects the design because the expansion difference between metal and cured compound is what puts the surrounding material in tension. Where the insert is large relative to the boss, that difference has to be absorbed by geometry rather than ignored, and the surface treatment of the insert matters if the joint is expected to stay tight in a humid environment.

Q3: How is insert position verified in production?

By measuring the insert, not the part outline: position, height and squareness relative to the datum surfaces that the assembly uses. Checking the part dimension alone can pass while the insert has tilted, which is why the control plan for an insert-molded part normally includes a dedicated check on the insert itself at a defined interval.

For technical data sheets, grade recommendations, or a discussion about your specific part and insert requirement:

📧 wendy.qiu@smcbmc.com  📞 +86-13868305300